. Copyright © 2003 by Harbor Freight Tools this manual or any artwork contained herein may be reproduced in any shape or form without the express written consent of Harbor Freight Tools.
For technical questions and replacement parts, please call 1-800-444-3353 06098 ®. ITEM Welding Current Duty Cycle Power Consumption Open Circuit Voltage Heat Control Ground Cable Torch Power Cable Power Cord Thermal Overload Protection with Light Wire Size Welding Material Size Wire Spool Size Weight Accessories You will need the manual for the safety warnings and precautions, assembly instructions, operating and maintenance procedures, parts list and diagram. Use of any other parts will void the warranty. Only use accessories intended for use with this tool. Approved accessories are available from Harbor Freight Tools. Do not operate tool if under the influence of alcohol or drugs. Read warning labels on prescriptions to determine if your judgment or reflexes are impaired while taking drugs.
Protective clothing should be free of holes, dry, and ANSI approved. This unit draws enough current to cause serious injury or death. Before turning the welder on, check the electrode holder to be sure that there are no protruding screw heads, and that all insulation is secure. Line Cord (13) Brush Hammer Handheld Shaded Face Shield If any parts are missing or broken, please call Harbor Freight Tools at the number on the cover of this manual as soon as possible. SKU 06098 Unpacking Ground Cable with Clamp. MIG Welder Unit Insert the Handle (4) into the Handle Sockets (3) and mount the Handle Sockets to the Side Panel B (1) top using supplied hardware. Lift Side Panel B (1) all the way to expose the wire spool and Wire Feed Mechanism (10). Mvelopes.
Refer to the power setting table on the next page. Thinner metals use lower current. Heavier metals use higher current. Verify that the On/Off Switch is in the OFF position, then plug the MIG Welder Line Cord into a dedicated, 120 VAC, 20 amp line with delayed action type circuit breaker or fuses. Overload protector will activate, the red Overload indicator will light, and the Arc Welder will turn off until it cools down.
If this happens, turn the On/Off Switch to the OFF position and wait about 3 5 minutes. Overload controller defective. Caution: Before performing any maintenance on the MIG Welder, unplug the power Line Cord from the electrical outlet. Periodically using compressed air, open the top and side panels and blow out all dust from the interior.
Store the unit in a clean and dry location. Periodically clean out the Torch Head.
Replacing the Wire Reel When the wire on the Feed Reel is used up, you will need to replace it as described on page 6, step 5 through step 9. NOTE: Some parts are listed and shown for illustration purposes only and are not available individually as replacement parts. Wire Feed Mechanism Assembly Drawing SKU 06098 Page 11. MIG Welder 131 Schematic Diagram MIG Welder 131 Assembly Drawing SKU 06098 Page 12. Hand Held Shield Assembly Drawing SKU 06098 Page 13.
This welder was originally a Chicago Electric 131 sold by Harbor Freight. It is modified to the extent I no longer consider it a Harbor Freight product. It's a Great Lake Innovations 131 MIG welder! The control board was completely re-designed to isolate the motor control completely from the welding circuit itself. It also has a separate motor driver circuit which is currently a prototype. None of this is finalized or cleaned up. Finally, there's a display which shows the Inches Per Minute at which the welder is feeding wire.
This is 100% a prototype part. Dico dvr software download. The display will eventually be mounted in the front.
. DUAL MIG WELDER 151 DUAL MIG WELDER 151 DUAL MIG WELDER 151 DUAL MIG WELDER 151 DUAL MIG WELDER 151 ASSEMBLY AND OPERATING INSTRUCTIONS 3491 Mission Oaks Blvd., Camarillo, CA 93011 Visit our Web site at Copyright © 2007 by Harbor Freight Tools this manual or any artwork contained herein may be reproduced in any shape or form without the express written consent of Harbor Freight Tools. l a i You will need the manual for the safety warnings and precautions, assembly instructions, operating and maintenance procedures, parts list and diagram. Keep your invoice with this manual. Write the invoice number on the inside of the front cover. Keep the manual and invoice in a safe and dry place for future reference.
Store idle equipment. When not in use, tools must be stored in a dry location to inhibit rust. Always lock up tools and keep out of reach of children. Do not force tool. It will do the job better and more safely at the rate for which it was intended. This unit draws enough current to cause serious injury or death. Before turning the welder on, check the electrode holder to be sure that there are no protruding screw heads, and that all insulation is secure.
Do not weld unless you are insulated from ground and the work piece. Connect only to a code approved power source. Connect only to a grounding power source conforming to the National Electrical Code and Local Codes. Wear proper clothing when welding. Use flameproof, welding-type gloves. Wear cuffless pants and pocketless shirt.
Both must be free of oil and grease. Wear high- topped, safety shoes with rubber soles. MIG Welder Unit Assemble the Axle (30) and Wheels (29) as illustrated in the Wheel Assembly Drawing at the end of this manual. Place the second wheel over the end of the Axle and secure in place with the Axle locking clip. Refer to the power setting table on the next page. Thinner metals use lower current. Heavier metals use higher current.
Verify that the On/Off Switch is in the OFF position, then plug the MIG Welder Line Cord into a dedicated, 220 VAC, 20 amp line with delayed action type circuit breaker SKU 55250 For technical questions, please call 1-800-444-3353. Note: If too much current is drawn from the MIG Welder, the Thermal Overload protector will activate, the red Overload indicator will light, and the Arc Welder will turn off until it cools down.
Chicago Electric Dual Mig 151 Manual
If this happens, turn the On/Off Switch to the OFF position and wait about 3 5 minutes. T l Caution: Before performing any maintenance on the MIG Welder, unplug the power Line Cord from the electrical outlet. Periodically using compressed air, open the top and side panels and blow out all dust from the interior. Store the unit in a clean and dry location.
Periodically clean out the Torch Head. Replacing the Wire Reel When the wire on the Feed Reel is used up, you will need to replace it as described on page 6, step 5 through step 9. I f i t c t i NOTE: Some parts are listed and shown for illustration purposes only and are not available. MIG Welder Dual 151 Assembly Drawing SKU 55250 For technical questions, please call 1-800-444-3353. Wire Feed Mechanism Assembly Drawing SKU 55250 For technical questions, please call 1-800-444-3353. Wheel and Axle Assembly Drawing MIG Welder Dual 151 Schematic Diagram SKU 55250 For technical questions, please call 1-800-444-3353.
Hand Held Shield Assembly Drawing SKU 55250 For technical questions, please call 1-800-444-3353.
Find quality MIG and flux welders on sale at Harbor Freight Tools today. Get the job done right with these high powered welders whether you’re welding stainless steel, sheet metal, cast iron or other metals. A flux welder is ideal for outdoor work because it doesn’t use an external shielding gas. If you’re looking for more versatility, chose a MIG/flux wire welder. It comes ready for Flux Core Arch Welding (FCAW) and also has the necessary components for MIG welding if you’re working inside or with thinner metals.
Find great deals today at HarborFreight.com. Harbor Freight Tools does not endorse any other business or organization or any technique in any customer and/or fan video. Always follow all of the instructions and warnings included with our products. We make no representation or warranty of any kind by including any customer and/or fan video on our website. LIFETIME WARRANTY Lifetime Warranty on Hand Tools! We guarantee our Hand Tools to be free from defects in material and workmanship for the life of the product.
Chicago Electric Mig 100
Limitations apply. ABOUT HARBOR FREIGHT TOOLS Founded in 1977, Harbor Freight Tools is the leading discount tool retailer in the U.S. Selling great quality tools at 'ridiculously low prices' in over 800+ stores nationwide and on its website. Harbor Freight Tools stocks over 7,000 items in categories including automotive, air and power tools, shop equipment and hand tools. With a commitment to quality and a lifetime guarantee on all hand tools, Harbor Freight Tools is a favorite of automotive and truck repair shops, government agencies, schools, manufacturers, contractors and tool enthusiasts who want top-quality and great selection and value.
The results speak for themselves - with over 40 million customers and thousands of people switching to Harbor Freight Tools every day.
Harbor Freight Tool's Quality Assurance headquarters in Calabasas, CA thoroughly and vigorously test Chicago Welding tools. The Quality Assurance division of Harbor Freight is dedicated to quality control, product testing, development and constant improvement. Testing in the QA lab simulates real-world conditions and environments, reflecting how the tools will actually be used and abused. Testing is performed throughout the production process and continues through post-production to both reduce the possibility of defects and to improve existing versions. Harbor Freight Tools does not endorse any other business or organization or any technique in any customer and/or fan video.
Always follow all of the instructions and warnings included with our products. We make no representation or warranty of any kind by including any customer and/or fan video on our website. LIFETIME WARRANTY Lifetime Warranty on Hand Tools!
Chicago Electric Mig Welder Manual
We guarantee our Hand Tools to be free from defects in material and workmanship for the life of the product. Limitations apply. ABOUT HARBOR FREIGHT TOOLS Founded in 1977, Harbor Freight Tools is the leading discount tool retailer in the U.S.
Selling great quality tools at 'ridiculously low prices' in over 800+ stores nationwide and on its website. Harbor Freight Tools stocks over 7,000 items in categories including automotive, air and power tools, shop equipment and hand tools. With a commitment to quality and a lifetime guarantee on all hand tools, Harbor Freight Tools is a favorite of automotive and truck repair shops, government agencies, schools, manufacturers, contractors and tool enthusiasts who want top-quality and great selection and value. The results speak for themselves - with over 40 million customers and thousands of people switching to Harbor Freight Tools every day.
Comments are closed.
|
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |